Consolidated Safety-Valve Co. v. Crosby Steam Gauge & Valve Co.

Ms. Justice Blatcheokd delivered the opinion of the court. On the 27th of May, 1879, the Consolidated Safety-Valve Company, a Connecticut corporation, brought a suit in equity, in the Circuit Court of the United States for the District of Massachusetts, against the Crosby Steam Gauge and Valve Company a Massachusetts corporation, for the infringement of letters patent No. 58,294, granted to George W. Richardson, September 25,1866, for an improvement in steam safety-valves. The specification of the patent is as follows: “ Be it known, that I, George W. Richardson, of the city of Troy, in the county of Rensselaer, in the State of New York, have invented a new and useful improvement on a safety-valve for steam generators, and I do hereby declare that the following is a full, clear and exact description of the construction and operation of the same, reference being had to the annexed drawings, making a part of this' specification, in which Fig. 1 is an end view of my improved safety-valve and its seat, as seen from the bottom; Fig. 2 is an end view of the valve aloné, as se4n from the bottom; Fig. 3 is vertical section at x x, Fig 1, of the valve and seat in position; Fig. 4 is a vertical' section at y y, Fig. 2, of the valve alone. Similar colors and letters of reference indicate corresponding parts in the several figures. A A is the head of the safety-valve; B B B B are wings to guide the valve into its seat E F; c c is a circular or annular flange or lip, extending over, slightly below, and fitting loosely around, the outer edge of the valve-seat E E; D D is a circular or annular chamber, into which the steam immediately passes when the valve lifts from its seat at the ground joint F F\ E E is the valve seat; F F is the ground joint of the valve and seat; P is the countersink or centre upon which the point of the stud extending from the scale lever rests, in the usual manner. The nature of my invention consists in increasing* the area of the head of the common safety-valve outside of its ground joint, and' terminating it in such a way as to form an increased resisting surface, against which the steam escaping *160 from the generator shall act with additional force after it has lifted the valve from its seat at the ground joint, and so, by-overcoming the rapidly increasing resistance of the spring or scales, insure the lifting of the valve still higher, thus affording so certain and free a passage for the steam to escape as effectually to prevent the bursting of the boiler or generator, even when the steam is shut off and the damper left open. “ To enable others skilled in the art to make and use my invention, I will proceed to describe its construction and operation. To the head of the common safety-valve, indicated by all that portion of Fig. 2 lying within the second circle from the common centre, I add what is indicated by all that portion lying outside of the said circle, in about the proportion shown in the figure. A transverse vertical section of this added por *161 tion. is indicated, in Fig. 4, by those portions of the figure lying outside of the dotted Ymes p.p, p p, while all that portion lying within the dotted lines p p,p p, indicates a transverse vertical section of the common safety-valve alone. This increased area may-be made by adding to a safety-valve already in use, or by casting the whole entire. I terminate, this addition to' the head of the valve with a circular or annular flange or lip, o c, which projects beyond the valve-seat E E, Fig. 3, and extends slightly below its outer edge, fitting loosely around it, and forming the circular or annular chamber D D, whose transverse section, shown in the figure, may .be of any desirable form or size. This flange or lip o c, fitting loosely around the valve-seat E E, is separated from it by about - of an inch, for an ordinary spring or balance. For a strong spring or balance this space should be diminished, and for a weak spring or balance it should be increased, to regulate the escape of the steam, as required. Instead of having the flange or lip c o project beyond and extend below and around the outer edge of the valve-seat, as shown in Fig. 3, a similar result may be obtained by having the valve-seat itself project beyond the outer edge of the valve-head, and terminating it with a circular or annular flange or lip, extending slightly above, and fitting loosely around, the outer edge of the flange or lip c o of the valve-head; but I consider the construction shown in Fig. 3 preferable. With my improved safety-valve, constructed as now described, and attached to the generator in the usual way, the steam, escaping in the direction indicated by the arrows in Fig. 3, first lifts the valve from its seat at the ground joint EE, and then, passing into the annular chamber D D, acts against the increased surface of the valve-head, and by this means, together with its reaction produced by being thrown downwards upon the valve-seat E E, it- overcomes the rapidly increasing resistance of the ’ spring or balance, lifts the valve still higher, and escapes freely into the open air, until the pressure in the generator is reduced to the degree desired, when the valve will be immediately closed by the tension of the spring or balance. The. escape of the steam by means of this safety-valve is so cértain and free, that' the pressure of the steam in the generator or boiler will *162 . not increase beyond the point or degree at which the valve is set to blow off.” The claim of the patent is this: “.What I claim as my improvement, and desire to secure by letters patent, is a safety. valve with the circular or annular flange or lip o o, constructed in the manner, or substantially in the manner, shown, so as to operate as and for the purpose herein described.” On the 2d of June, 1879, the same plaintiff brought-a suit in equity,.in the same court, against the same defendant, for the infringement of letters patent No. 85,963, granted to the same George W. Richardson,. January 19, 1869, for an improvement in safety-valves for steam boilers or generators. So much of the specification of the patent as is invblved in this suit- is as follows: “Be it known, that I, George William Richardson,.of Troy, in the State of New York, have invented certain new and useful improvements in safety-valves for steam boilers or generators ; and I do hereby declare that the following is a full, clear, and exáót description thereof, reference being had to the accompanying drawings making part of this specification, in which Figure 1 is a vertical section of the safety-valve and its connections, taken in the plane of the axis of the valve-stem; Fig. 2, a horizontal section taken in the plane of the line A a of Fig. 1, and Fig. 3 another horizontal section at the line B b of Fig. 1. Fig. 4 is a vertical section taken in the plane of the axis of the valve, representing a modification of my said invention ; and Fig. 5, a horizontal section thereof, taken in the plane of the line C c of Fig. 4. My said invention relates to improvements in the invention described in letters patent granted to me, and bearing date the 25th day of September, 1866, which said patented invention relates-to a means for providing a more free escape for the steam than could be obtained by safety-valves as constructed prior thereto, and to insure the keeping of the valve open until the pressure of the steam in the boiler or generator falls below the pressure which was required to open it, the said means so patented consisting in forming the valve with a surface outside of the ground joint, for the escaping steam to act against, the said surface being surrounded by *163 a projecting or overlapping lip, rim, or flange, leaving a narrow escape for the steam when the valve is opened; but which, although of greater diameter than the valVe-seat, by reason of *164 the said lap, presents a less area of opening for the escape of steam than is produced at the valve-seat, so that the steam which escapes through the area between the valve shall exert pressure against the.said surrounding surface, and thereby not only open the valve completely, but hold it up until the pressure of the steam in the boiler falls below the pressure by which the valve was opened. “ One part of my present invention relates to .a means for regulating or adjusting the area of the aperture for the escape of the steam after acting on the said surface outside of the valve-seat, so that the valve may be set to close at any desired pressure below the pressure- which will open it; and this part of my invention consists in making the aperture or apertures for the escape of the steam, after it has acted on the said surface outside of the valve-seat, adjustable. . . . • “I will first describe the preferred mode of application of my said invention, as represented in Figs. 1, 2, and 3 of the accompanying drawings. In the said figures,. a represents the valve-seat, which is to be attached to a steam boiler or generator in the usual or any other, suitable manner, and which is formed, in the usual manner, with a bevelled seat from the valve 5, fitted thereto by what is well known as a ‘ ground joint.’ . . . “ It is desirable, that, so soon as the pressure of the steam in the boiler or generator reaches the pressure at which it should be relieved, the safety-valve should open wide for the free escape of steam, and that the valve should remain open until the pressure in the boiler is reduced below the pressure by which the valve was opened, and that it should be so organized that the engineer may be able to adjust it so that it will close at any desired number of pounds pressure below the pressure at- which it was opened. To accomplish these results was the main object of my said invention. “ To the upper surface of the valve I secure a cap-plate or annulus, m, formed with a downward-projecting flange, n, at its outer periphery, leaving an annular space, o, all around between the outer periphery of the valve and the inner periphery of the flange n of the said cap. And the upper surface of the valve-seat a is extended' all around, a little beyond the outer *165 periphery of the flange n of the cap, leaving an annular sur-' face, p, surrounded by an upward-projecting rim, q, the plane ol the upper edge of which, when the valve is closed, extends a short distance above the plane of the lower edge of the'flange n of the cap. The said cap-plate m is connected with the top of the valve by studs r r, or cast with it, in such manner as to leave an open space, s, between the two, for the passage of steam to the central aperture t in the cap, through which steam can escape when the valve is lifted from its seat. This central aperture is" surrounded by a projecting cylindrical flange, threaded on the outside, to which is fitted a threaded ring, u, that can be turned up or down to any desired elevation, and there secured by a set-screw, v. The disk-like projection f, on . the valve rod or stem e. extends over the said central aperture i in the cap-plate m, and at such an elevation that the upper edge of the adjustable ring can be set in contact with it, or let down so far below it as to leave sufficient space for the free escape of steam. “ From the foregoing it will be seen, that, when the pressure of steam in the boiler or generator becomes sufficient to lift the valve from its seat, it acts against the surface of the annular, space o between the bevel of the'valve-seat and the downward-projecting flange n of the cap, to assist in lifting and holding up the valve, particularly when the valve is borne ' down by the tension of a spring, which presents' an increasing resistance as the valve is lifted. If the projecting rim q were in the same plane with the lower edge of the flange n, the diameter of these parts being greater than that of the valve-seat, on the lifting of the valve and cap, the area of the opening between the flange n of the cap and the projecting rim q would be greater than the area of the opening between the valve and its seat, just in proportion as the diameter of the one is greater than the other, and the steam escaping from, the valve would pass unchecked between the flange n and rim q, and would not exert any force against the surface of the annular space o; but, as the rim q extends above the lower edge of ,the flange n of the cap-plate, it follows that the aperture between the valve and its seat, by the lifting of the valve, is *166 always greater than the aperture between the flange n and the rim q, and hence the escaping steam, by its elastic force, will act against the surface of the annular space o, to assist in lifting and holding up. the valve until the pressure in the boiler or generator falls below7 the pressure by which the valve was first opened. The difference between the pressure against which the valve will close and the pressure by which it will be opened will depend upon the distance between the outer periphery of the flange n of the cap-plate and the inner periphery of the projecting rim q. To render this adjustable, the area of the aperture for the escape of steam beyond the valve-seat must be adjustable. • This is effected by the raising or lowering of the ring u. If it be set to its lowest position, the steam escaping from the valve will be free to escape between the top of the valve and the cap, through the central aperture, and thence between the upper edge of the ring u and the disk f, without materially aiding to lift or hold up the valve; but, by setting the ring u nearer to the under surface of the disk/1, and thereby reducing the space for the escape of steam, it will be caused to act, by its elastic force, against the annular space o of the cap-plate, and thus assist in lifting the valve and holding it up. “ I have described and represented this as the simplest mode of adjusting tke area of the aperture for the escape of the steam after it passes the valve-seat; but it will be obvious, that the same result may be attained by equivalent means, such, for instance, as making the ring q in adjustable segments, so that its diameter can be increased or diminished; but this would be more complicated than the mode first and fully described; and it' will also be obvious, that the devices for holding up the valve may be inverted, as represented in Figs. 4 and 5 of the accompanying drawings, in which a' is the valve-seat and V the valve, with its bevelled .ground joint, the valve-seat a' having a flat annular surface c', beyond the bevel, and the valve an annular surface d', with a downward-projecting flange d, the lower edge of which, when the valve is closed, extends a little below the plane of the surface d of the valve-seat, and a narrow annular space being left for the escape of steam between the inner *167 periphery of the said flange and the outer periphery of the valve-seat a’, as set forth in my patent of September 25, 1866.” - The claim of the patent is as follows: “ What I claim as- new, and desire to secureijy letters patent, is, the combination of the surface beyond the seat off. the safety-valve, with the means herein desorbed for regulating of adjusting the area^of the passage.for the escape of steam, substantially as and for the purpose described.” The answers in the two suits set up want of novelty, and cite, as anticipating patents, three English patents — one to Charles Ritchie, No. 12,078, August 3, 1818; one to James Webster, No. 1,955, July 12, 1857; apd one to William Hartley, No. 2,205, August 19, 1857; also, an English publication made in 1858, called “The Artizan/’ Infringement is.denied, and it is averred that the valves which the defendant makes and sells are the inventions of George H. Crosby, and are described in two patents granted/to him and owned by the defendant, one No. 159,157, dated January 26, 1875; and the other, ¡No. 160,167, dated February 23^1875. The same proofs were taken in the two suits, and they were heard together in the Circuit Court. In each suit that court made a decree dismissing the bill, 7 Fed. Rep. 768, and from each decree the plaintiff has appealed. When Richardson applied for his patent of 1866 his claim read thus: “ What I claim as my improvement, and desire to secure by letters patent, is, increasing the area of the head of the.common safety-valve, outside of the ground joint-i'7F, and terminating this addition with the circular or annular flange or lip c <?,-constructed in the-manner, or substantially in the manner shown, 5t> as to operate as and for the purpose herein described.”- This claim was rejectedás 'defective, because not for a'device; and it was' amended-to read as granted. In the application for the patent of 1869 there were two claims. The' second related to means for preventing the guides and stem-of the valve from binding, and was rejected as not new, and stricken oiit;-though the descriptive matter on which it was founded was retained. The first - claim,, as applied for, *168 ..was this: “What I claim as new, and desire to.secure by letters patent, is, combining with the surface beyond the bevelled, or equivalent, seat of a safety-valve, the means herein described, or the equivalent thereof, for regulating or adjusting the area of the passage for the escape of steam beyond the bevel, or equivalent, seat, substantially as and for the purpose described.” This claim was amended, on suggestions made by the Patent . Office, to.read as granted. ; The view taken by the Circuit Court, in dismissing the bjills, was, that some valves had been made before 1866, which embodied the same general principle as Richardson’s, and'were of some value, operating through the expansive power of steam exerted upon an additional chamber outside of the ground joint; and that what Richardson did was to so regulate the action of the chamber outside of the ground joint, by a crack or opening between the 'lip of the valve and its main body, that the steam would be confined or huddled, when it sought to escape from the chamber, and so the valve would be held- up just long enough, and could fall rapidly before too much steam was lost. But, the cases went off on the question of infringement, and the Circuit Court found, that while the defendant’s valve employed an additional surface to lift the valve as soon as it began to blow, and the pressure was regulated in- part by a stricture, it differed from the plaintiff’s, in that the additional area was not outside of the ground joint, but inside, and was not acted on independently of the valve itself, but was a part of it, and the escaping steam did not act at all by impact, but wholly by expansion. The conclusion ivas, that as Richardson was not the first t.o apply the idea of an additional area or of a stricture, he could not enjoin a valve which resembled his only in adopting such general ideas, and that his claims did not cover a valve having the mode of operation of the defendant’s. Edward H. Ashcroft, as assignee of William Naylor, obtained reissued letters patent of the Unitfed States; No. 3,727, dated November 9, 1869, on the surrender rf letters .patent No. -58,962, issued to said Naylor, October-16; 186t for an improvement in safety-valves. Ashcroft brought a- si k in equity, in the Circuit Court of the United States for the-Dkfcriot of Mas *169 sachusétts, against the Boston and Lowell Railroad Company, for the infringement of reissue No. 3,727. The infringement consisted in the use of valves constructed according to the patent of 1866 to Richardson. The court dismissed the bill, 5 Off. Q-az. 725, and 1 Holmes, 366, and 1" Bann. & A. 215, and on.an appeal to this court, by the plaintiff, the decree was affirmed. 97 U. S. 189. In view of an English patent, No. 1,038, granted to Charles Beyer, April 25, 1863, it was held by this court,'that Naylor was not the first person who devised means for using the recoil action of steam to assist in lifting the valve, or who invented the combination, in a spring safety-valve, of an overhanging downward curved lip, with an annular recess surrounding'the valve-seat, into which steam is deflected as it issues between the valve and its seat. In speaking of the invention of Richardson, as described in his patent of 1866, this court said: “ His invention, as he describes it, consists in increásing the area of the head of the common safety-valve outside of its ground joint, and terminating it in such a way as to form an increased resisting surface, against which the steam escaping from the generator shall act with additional force, after lifting the valve from its seat at the ground joint, and so, by overcoming the rapidly increasing resistance of the spring or scales, will insure the lifting of the valve still higher, thus affording so certain and free a passage for the steam to escape as-effectually to-prevent the bursting of the boiler or generator, even when the steam is, shut off and the damper left open. Safety-valves previously in use were not suited to accomplish what was desired, which was to open for the purpose of relieving the boiler, and then to close again at a pressure as nearly as possible equal to.that at which the valve opened. Sufficient appears, to show that Richardson so far accomplished that purpose as to invent a valve which would open at the given pressure to which it was adjusted, and relieve the boiler, and then close again when the pressure was reduced about two and one-half pounds to the inch, even when the pressure in the generator was one hundred pounds to the same extent of surface, which made it, in practice, a useful spring safety-valve, as proved by the fact that it went almost immediately into gen *170 eral use. . . . When the valve opens the steam expands and flows into the annular space around the ground joint. Its free escape,'which-might otherwise be too free, is prevented by a stricture or narrow space formed by the outer edge of the lip and the valve-seat. By these means, the steam escaping from the valve is made to act, by its expansive force, upon an additional area outside of the device, as ordinarily constructed, to assist in raising the valve.” On these views, it was held by this court, that, although important functions, not very dissimilar in the effect produced; were performed by the two valves there in controversy, the means used and the mode of operation were substantially different in material respects. In the present case,-the defendant,has introduced in evidence the before-named English patents to-Ritchie, Webster and Hartley, and the English patent to William Naylor, No. 1,830, granted July 1,1863; and also letters patent.of the United States, No. 10,243, granted to Henry Waterman, November 15,1853, and the reissue of the same, No. 2,675, granted to him July 9, 1867. In view of all these patents, and of the state of the art, it appears that Richardson was- the first person who described and introduced into use a safety-valve which, while it automatically relieved the .pressure of steam in the, boiler, did not, in effecting that result, reduce the pressure to such an extent as to make the use of the -reliving apparatus practically impossible, because of the expenditure of time and fuel necessary to bring up the steam again to the proper working standard. His-valve, while it automatically gives relief before the pressure becomes dangerously great, according to'the point-at "which the valve is set to,blow off, operates so as to automatically arrest with promptness the reduction of pressure when the boiler is relieved:"'/íf'is patent of 1866 gave a moderate range of pressure, as the result of the proportions there specified, and his patent of 1869 furnished a "means of regulating that -range of pressure, by a screw ring, within those narrow limits, which are essential in the use of so subtle an agent as steam. In regard to allpf the above patents, adduced against Richardson’s /.patent óf 1866, it may be generally said, that they *171 never, were, in their day, and before the date of that patent, or of Ri'chardson’s invention, known or recognized as producing any such result as hisf apparatus of that patent produces, as above defined. Likenesses in them, in physical structure, to the apparatus of Richardson, in important particulars, may be> pointed out, but it is only as the anatomy of a corpse resemblés that of the living being. The prior structures never effected the kind oí result attained by Richardson’s apparatus, because they lacked the thing which gave success. They did not have the retarding stricture which gave .the..alifting opportunity to the huddled, steam, combined with the quick falling-of the valve after relief had come: Taught by Richardson, and by the use of his apparatus, it is not difficult for skilled mechanics to take the prior structures and so arrange and use them as to produce more or less of the beneficial results first made known by Richardson; but, prior to 1866, though these old patents and-their descriptions were accessible, no valve was made producing any such results. Richardson’s patent of 1866 states that, the addition to the head of .the valve terminates in an'annular lip, which fits loosely around the valve-seat, and is separated from it by about -^th of an inch for an ordinary spring, and a less space for a strong spring, and a greater space for a weak spring, forming an annular chamber, and regulating the escape of the steam; that the steam, when the valve is lifted, passe?, beyond the valve-seat, and into the annular chamber, and acts against the increased surface of the valve-head, and thus overcomes the increasing resistance of the spring due to its compression, and lifts the valve higher, and the steam escapes freely into the open air, until the pressure is sufficiently reduced, when the spring immediately closes the valve. It is not shown that, before 1866, any known valve produced this result. On the contrary, Richardson.testifies, that, for about twenty years before 1866, he was acquainted with safety-valves in practical use, by working in the locomotive repair shops of railroad companies, part of. the time as foreman, and as a locomotive" engineer, and that he never, before his invention, knew, in practical use or on sale, of any spring-loaded safety-valve, capable of opening to relieve the boiler when the working *172 pressure was exceeded, and' of automatically closing with a small loss of working-pressure. He also says that he was in England, for about four months, in 1873, bringing his valve to the notice of officials in the shops of some of the largest railroad companies (his valve being one especially useful on locomotive engines on railroads); that, while he was in England, he found no man who professed to be acquainted with, or to have heard of, a safety-valve which would' automatically open and relieve the boiler at a predetermined working pressure, and automatically close when such working pressure had been slightly reduced, or who admitted that such a valve could be made until he had seen Richardson’s valve work; that the master mechanics at the shops named did not believe he could make a valve close within 25 pounds of the blowing-off point; that he showed them the working of his valve with no excess beyond working pressure, and with but from 3 to 5 pounds reduction from a pressure of 130 pounds per square inch in the boiler; that he did not hear, in England, of any of the Ritchie, Webster or Hartley valves, but heard the Naylor.valve blow; and that, when it blew, the steam rose several pounds above the point where it commenced to blow, and it did not close promptly, tightly or suddenly. There is no evidence to contradict, or vary the effect of, this testimony. Thomas Adams, of Manchester, England, who has spent a lifetime in the manufacture and practical working of safety-valves, testifies, that the Ritchie and Webster valves have never been in use practically in England, and the Hartley only in two or three cases, when it was a failure; that he himself has made and applied, in England, about 15,000 of Richardson’s valves; that, if loaded at 120 pounds per square inch, his valve returns to its seat with a very small loss of pressure; that the Beyer valve, loaded at 120 pounds, reduces the pressure 30 pounds, before returning to its seat; and that Naylor’s has been- superseded by Richardson’s. It appears to have been easy enough to make a safety-valve which would relieve the boiler, but the problem was to make " one which, while it opened with increasing power in the steam against the increasing resistance off a spring,- would close sud *173 denly and not gradually, by the -pressure of the same spring against the steam. This was a problem of the reconciliation of antagonisms, which so .often recurs in mechanics, and without which practically successful results are not attained. What was needed was a narrow stricture, to hold back the escaping steami, and secure its expansive force inside of-the lip, and thus aid the direct pressure of the steam from the boiler, in lifting the valve against the increasing tension of the spring, with the result, that, 'after only a small, but a sufficient, reduction in the boiler pressure, the compressed spring would, by its very compression, .obtain the mastery and close the valve quickly. This ■problem was solved by Richardson and never before. His patent of 1869 describes the arrangement and operation of the whole apparatus, with the adjustable ring, thus: When the pressure of the steam lifts the valve, the steam acts against the surface of an annular space between the bevel of the valve-seat and the downward projecting flange of the cap-plate, to assist in holding up the valve against the increasing resistance of the spring.. The aperture between the valve and its seat is always greater than that between the flange and the upward projecting rim, and thiis the steam in the annular space assists in holding up the valve till the boiler pressure falls below that at which the valve opened. The difference between the closing pressure and the opening pressure depends on the distance between the flange and the rim. There is a central aperture in the cap, through which the steam escapes when the valve is lifted, which is surrounded by a projecting cylindrical flange, threaded on the outside, to which is fitted a threaded ring, which can be turned up or down, and secured by a set screw. By this means, the area of the aperture for the escape of steam beyond the valve-seat is adjustable, the space being largest when the ring is down and smallest when the ring is up. Ritchie’s patent, in speaking of his valve, says: “ This valve is.weighted by a helical spring i (shown at Figure 2) of sufficient power according to ■ the required pressure of the steam ; and, when it is intended to be used as a reserve safety-valve, I "place the spring around that part of the stem below the valve, that is to say, within the boiler,1 as shown at Figure 2. The *174 advantage of this form of construction of valve over the ordinary valve is as follows: As soon as the pressure of the steam raises the valve from its seat, the flange h, being exposed to the pressure of the steam, presents an increased surface, which compensates for the increasing resistance of the helical spring i, until the valve.has been raised to a height equal to the area of the steam-way, when it allows the steam or vapor to escape freely.” In an article in “ The Artizan,” published in England, in July, 1858, signed by Ritchie, and referring to his patent of 1848, it is said of his valve: “ The top area being made double that of the under side or steam-way, such a valve would quickly reduce the pressure in the boiler to. half that at which the valve lifted; and so, also, of other proportions. Hence it is chiefly suited for a reserye valve.” ' This shows the existence of the very, evil whichRichardson.remedied.’ Ritchie’s patent and publication say nothing about any stricture. The evidence in the present’ case shows satisfactorily, that valves made in conformity with the measurements of the drawing of Ritchie’s patent do, in practice,- reduce the pressure in the boiler to such an extent, after that pressure is properly relieved, and before they close, as to involve great loss of time and consumption of fuel before the initial pressure is restored. The experimental valves produced by the defendant as structures made according to Ritchie’s patent vary from the dimensions of his drawing, and the variations are those which result from the instructions given by .Richardson in . his patients. Ritchie gives no information how to make a. valve work at a predetermined pressure, or hoW to make it work with a small range or difference between the opening and closing pressures,' or how to proportion the strength of the spring and the size of the stricture.to each other. ’ The’ same thing is true of the Webster and-the Hartley patents. ' The Webster patent shows a huddling chamber and a stricture. . But the evidenpe shows that valves made with the proportions shown in the drawings of Webster work with so large .a loss of coffer-pressure,- before closing, ás to be practically and economically worthless. Webster’s patent describes a means of making the aréa-ior the . escápe of steam adjustable, consist *175 ing in adjusting up and dowp, on a smooth valve-stem, a sliding collar'or flange, and fixing it in place by a set-screw. But it does not show the screw-ring of Richardson, with its minute' delicacy of adjustment and action. ' Nothing'further need be said as to the Hartley valve or the Beyer valve. The original patent to Waterman was issued in 1853. His attention, had been turned to the subject of safety-valves for locomotive engines. He invented what is described in that patent, but he testifies that, before 1866, he never saw a safety-valve capable of keeping the pressure at a point not above working pressure, and of relieving the boiler with but a small loss of pressure; that his valve would let the-steam down about 15 pounds, and was not practical for an-ordinary locomotive; and that the Richardson valve, when introduced, went at once into general use. The Waterman valve had a supplemental surface, oil which the steam acted to aid in the raising of the valve; and this was shown in the drawing of Waterman’s original patent, hut the specificátion did not describe it. Waterman’s original patent did not show the. use of a spring, and prior to its reissue his valve had not been made with a spring. After Richardson obtained his patent of. 1866, and Waterman knew of Richardson’s valve, they cómbined the in- ' terests in their two patents, and the reisue of Waterman’s was obtained, with the co-operation of' Richardson, he signing as a witness the specification of the reissue. That specification, granted in 1867, describes an overhanging part of the valve as increasing its area outside of, and beyond, the ground joint, and a concentric rim or ledge, which directs the steam upward against such overhanging part of the valve, so that the valve is assisted in rising. The specification was drawn in view of Richardson’s patent and valve, and for the purpose of making a claim, which was then made, and which was not in Waterman’s original patent, to a combination of the concentric rim or ledge with the overhanging part of the valve. The specification states, that the valve and its seat are so constructed that the escaping steam will act on an increased area. of the valve after it has risen from its seat, and strike the overhanging or *176 projecting annular surface above, and outside of; and beyond, the ground joint. It also states, that a proper modification of the overhanging or projecting annular surface will modify the force of the steam; that, if such surface be large, the valve will be opened suddenly and discharge so much steam that the pressure in the boiler will be considerably reduced before the valve closes; that such surface may be made so small that but little more than the surplus steam will escape; that the success or efficiency of the valve will depend on a proper proportion between the overhanging annular surface and the .concentric rim or ledge, because, if a free discharge of steam between them is allowed, the valve will not be assisted in rising, and, if the escape of steam is too small, the valve will rise too easily, and remain open too' long, and the steam villi be so much reduced in pressure as seriously to impair the economical and efficient action of the apparatus; and directions are given as to the sizes of the overhanging part, and of the ledge or rim, and of the opening, for a valve of a specified diameter, acting with a specified pressure of steam. Nothing of all this was found in the specification of the original Waterman patent- It, therefore, has no effect, as against Richardson’s patent of 1866, to destroy the validity of that patent. If anything which Richardson did in respect to reissuing the Waterman patent, could, in any event, affect the rights of the present plaintiff under either patent sued on, as to which we express no opinion, it is sufficient to say, that the present defendant claims, in its answers, no benefit from any action of Richardson’s in respect to the Waterman patent, as operating in its favor or inuring to its benefit, as an ■ equitable defence in these suits. Richardson is, therefore, entitled to cover, by the claim of his patent of 1866, under the language, “ a safety-valve with the circular or annular flange or lip o o, constructed in the manner, or substantially in the manner, shown, so as to operate as and for the purpose herein described,” a valve in which are combined an initial area, an additional area, a huddling chamber beneath the additional area, and a strictured orifice leading from the huddling chamber to the open air, the orifice being *177 proportioned to the strength' of the spring, as directed. The direction given in the patent is, that the flange or lip is to he separated from the valve-seat by about -¡/j-th of an inch for. an ordinary spring, with less space for a strong spring, and moré space for a weak spring, to regulate the escape of the steam, as required. As matter of law, this description is sufficient, within the rule laid down in Wood v. Underhill, S. How. 1, and it is not shown to be insufficient, as a matter of fact. ■ Eichardson is also entitled to cover, by the claim of his patent of 1869, under the language, “ the combination of the surface beyond the seat of the safety-valve, with the means herein described, for regulating or adjusting the area of the passage for the escape of steam, substantially as and for the purpose described,” the combination with the surface of the huddling chamber, and the strictured orifice, of a screw ring, to be moved' up or down to obstruct such orifice more or less, in the manner described. The Eichardson patents have a disc valve, an annular huddling chamber, an annular stricture at the outer extremity.,pf the radii from the centre of the valve, an additional area which is radially beyond the disc.valve, and a cylindrical steam-way. But, before 1866, an annular form of safety-valve was well known. Such a valve necessarily requires an annular steam-way. In the defendant’s valve, complainant’s Exhibit A, the same effects, in operation, are produced as in the Eichardson valve, by the means described in Eichardson’s claims. In both structures, the valve is held to its seat by a spring, so compressed 'as to keep the valve there until the pressure inside of the boiler is sufficient to move the valve against the pressure of the spring, so that the steam escapes through the ground joint into a chamber covered by an extension of the valve, in which chamber the steam acts expansively against the extended surface, and increases the pressure in opposition to the increasing pressure of the spring, and assists in opening the valve wider; this chamber, in the defendant’s valve, has, at its termination, substantially the same construction as Eichardson’s valve, namely, a stricture, vhich causes the steam to act, by expansive *178 force, against the extended surface of the valve; and in both valves, after the pressure of the steam has been somewhat reduced in the boiler, the closing movement is quickened, as the valve nears its seat, in consequence of the reduced pressure of the steam on the extended surface, and the valve comes' suddenly to. its seat. In the Richardson valve, the valve proper is a disc, and the extended surface is an annulus surrounding the disc, while, in the defendant’s valve, the valve proper is an annulus, and the extended surface is a disc inside of the annulus. But this is a mere interchange of form between the valve proper and the extended surface, within the skill of an ordinary mechanic. There is one structural difference between the two valves, which is now to be mentioned. In the Richardson valve, all the steam which escapes into the open air escapes from the huddling chamber, through a stricture which is smaller than the aperture at the ground joint. In the defendant’s valve, the valve proper has two ground joints, one at the inner periphery of the annulus, and the other at its outer periphery, and only a part of the steam, namely, that which passes through one of the ground joints passes into the huddling chamber and then through the stricture, the other part of the steam passing directly from the boiler into the air, through the other ground joint. But all of that part of the steam which passes into the huddling chamber and under the extended surface, passes through'the constriction at the extremity of such chamber, in both valves, the difference being only one of degree, but with the same mode of operation. In the Richardson patent of 1869, the stricture is regulated as to size by an adjustable screw-ring. In the defendant’s valve, there is a screw-ring or sleeve, which closes the escape orifices from the central chamber, more or less. In the defendant’s valve, the huddling chamber is at the centre instead of the circumference, and is in the seat of the valve under the head, instead- of in the head, and the stricture, instead of being at the circumference of the head, is at the circumference of the seat of the valve. But this is only the use of means equivalent to those shown by Richardson, while the *179 mode of operation of the parts of the mechanism is the same, in their relation to each other, and the result is the same. Richardson’s invention brought to success what prior inventors had essayed and partly accomplished. He used some things which had been used before, but he added just that which-was necessary to make the whole a practically valuable and economical apparatus. The fact that the known valves were not used, and the speedy and extensive adoption of Richardson’s valve, are facts in harmony with the evidence that his valve contains just what the prior valves lack, and go to support the conclusion at which we have arrived on the question of novelty. When the ideas necessary to success are made known, and a structure embodying 'those ideas is -given to the world, it is easy for the skilful mechanic to vary the form by. mechanism which is equivalent, and is, therefore, in a case of this kind, an infringement. It follows, from these views, that The decrees of the Circuit Court must he reversed■, and each case he remanded to that court, with a direction to enter a decree sustaining the validity of the patent sued on, and decreeing infringement, and awarding an account of profits and da/mages, as prayed for, and to take such further proceedings as may he proper and not inconsistent with this opinion,. and with the further direction, as to the suit brought on the patent of 1869, to gra/nt a perpetual injunction, according to the prayer of the hill.