McCarty v. Lehigh Valley Railroad

Mr. Justice Brown, after stating the case, delivered the opinion of the court. The specification of the patent in this case does not, as specifications ordinarily do, state the peculiar functions of the patented device, the defects it is designed to remedy, or the features that distinguish it from other similar devices. This dmission, however, is supplied by the testimony, which shows that the invention was due to the frequent breaking of wooden bolsters, of the form in common use, in what were termed the “ diamond truck,” and other forms of car trucks. After some fruitless experiments, McCarty conceived the idea of using two iron plates, thereby forming a strong bolster, without the disadvantage found in the use of wood alone, or wood in connection with the iron plates. This resulted in the application for patent No. 339,913, for a bolster partly supported by truss rods. It soon appeared, however, that the form shown in the drawings of 339,913 possessed the requisite strength without the truss rods, which were accordingly dispensed with, and patent No. 314,459 subsequently applied for. A few days after McCarty applied for his first patent, viz., September 10, 1883, one "William H. Montz made application for a similar device,. upon which a patent was granted, apparently by mistake of the Patent Office, and an interference then declared between them. Priority in invention was awarded to McCarty, February 24, 1886, neither party taking any. testimony. In this connection there was much evidence tending to show that in October, 1882, a convention of master car builders was held at Niagara Falls, at which McCarty’s model was exhibited and examined by car builders, among whom was Mr. Lentz, master car builder of the Lehigh- company, defendant in this case. Shortly after this Mr. Lentz wrote an official letter in behalf of the defendant, requesting McCarty to send a blue-print of his truck, as shown at Niagara Falls the week before. A blue-print was accordingly sent to him on October 24, which eor *114 responded with the drawing annexed to patent No. 339,913, soon after which the defendant company began the manufacture of bolsters for use in their cars substantially after the form in the blue-print, and in the following year, Montz made application for the patent upon which the interference was declared between him and McCarty, which resulted in awarding priority of invention to McCarty. But this question of priority, if not settled conclusively by the interference, becomes immaterial in this case in view of the anticipating device set up as a defence, which if sustained would probably apply as well to the one patent as to the other. Freight cars are generally, if not universally, constructed so as to ride upon two four-wheeled trucks, upon which the cars are supported by means of devices called bolsters. One of these devices is attached to the bottom of the car body, and is ■called a body bolster. The other is attached to the truck, and is called the truck bolster. The body bolster rests upon the truck bolster, and at the point of contact there is a device called the centre bearing plate, which, acting in connection with a king bolt, permits the truck to conform to inequalities and curvatures in the track, regardless of the direction of the axis of the car body. Side supports, shown as J in figure 2, are also furnished, to secure stability of the car upon the truck, and prevent any tendency to upset, by limiting the rocking of the car body. Ordinarily, though, the weight, is carried upon the centre bearing plate, that the swivelling may be done as easily as possible, in order to avoid friction between the car and the side bearings, especially in hauling a heavy train around a curve. Truck bolsters are sometimes set rigidly upon the truck frame. These, however, were found defective since, in case of inequalities in the track, the sinking of bad joints, the unevenness of side tracks and their approaches, and more especially in cases of derailment, the trucks were subjected to a severe torsional strain, which racked them, loosened their bolts, and weakened their entire structure. To obviate this, it had become common to rest the ends of the bolster upon springs in the side trusses between the wheels, as shown in figure 1, and *115 also in several prior patents. These are termed floating bolsters, the object of which is to relieve the car from shocks caused by any unevenness of the tracks or roadbed. Bolsters made of wood, which were formerly used and found to be sufficient under light loads, especially when trussed, were, when used to carry the heavy loads of modern cars, which are. double, and even triple the weight formerly carried, found insufficient, and have largely given place to bolsters of iron. The bolster in question consists of two bars of metal, F and Gr, placed one upon the other, the lower one, Gr, being horizontal, and the upper one, F, arched so as to form the truss. The lower bar is made longer than the upper, and its ends are turned up into flanges, Q, so as to form abutments or bearing surface for the ends. of the upper bar, and thus to receive the end thrust caused by the weight imposed upon the bolster. Between the two bars, at their central point, are supports or columns, HH, which rest at their lower ends upon the lower bar and hold upon their upper ends the upper bar, fastening bolts being passed through the bars and the columns. Similar short columns, MM, are placed between the bars at the point where the arch of the upper bar begins. To the' under side of the bolster so formed is bolted a plate, P, which serves to guide the bolster between the columns of the truck frame, the sides of this plate being notched, as shown at a, so as to fit around the columns of the truck frame. In connection with this truck bolster, there are truss rods, K, which pass diagonally through castings placed upon the upper side of the truss, and aré supported upon seats under the lower bar, and provided with the usual screw threads and nuts for giving them the proper degree of tension. These truss rods, however, form no part of the third and fourth claims in dispute. These claims differ from each other principally in the fact that the flanges Q at the ends of the lower bar Gr, as well as the pillars H, constituting elements in the third claim, are not found in the fourth; while the fourth describes the plates P, which are stated' in the third claim to be “ bolted to the ends of said bars under the same,” as “ secured beneath the bars *116 FGr at their ends, and notched or grooved on their sides at a, to receive the columns B of the side irons, substantially as and for the purpose set forth.” There is no suggestion in either of these claims that the ends of the bolster rest upon springs in the side trusses, although they are.so.described in the specification and exhibited in the drawings. It is suggested, however, that this feature, may be read into the claims for the purpose of sustaining the patent. While this may be done with a view of showing the connection in which a device is used, and proving-that it is an operative device, we know of no principle of law which would authorize us to read into a claim an element which is not present, for the purpose of making out a case of novelty or infringement. The difficulty is that if we once begin to include elements not mentioned in the claim in order to limit such claim and avoid a defence of anticipation, we sliould never know where to stop. If, for example, a prior device were produced exhibiting the combination of these claims plus the springs, the patentee might insist upon reading some other element into the claims, such for instance as the side frames and all the other operative portions of the mechanism constituting the car truck, to prove that the prior device was not an anticipation. It might also require us to read into the fourth claim the flanges and pillars described in the third. This doctrine is too obviously untenable to require argument. The court below dismissed the bill upon the ground that the patent had been substantially anticipated by prior devices, which required nothing more than mechanical skill to adapt them to the purposes of this patent. In this connection, defendant introduced a-device known as the “Old Metal Transom,” which appears to have existed prior to 1882, and probably before the date of the McCarty invention, which he fixes as in June, 1881, although from his correspondence with the Patent Office it appears very doubtful whether he perfected it before July, 1882. This transom was used not as a truck bolster, but as a body bolster, and consisted of a straight bar corresponding to the bar Gr, having the flanges Q at the end, a bent bar corresponding to F, and interposed columns corre *117 sponding to the columns M. It is in fact the McCarty holster turned upside down, with the plates P, which are only necessary in a floating bolster, omitted. The only object of these plates, fitted as they are with notches to embrace the columns of the side trusses, is to serve as a guide for the ends of the bolster as they rise and fall upon the springs. Defendant also exhibited the Naugatuck truck, which appeared to have been used upon the Naugatuck Railroad in. the State of Connecticut as early as 1862, and' was still in actual use upon the New York, New Haven and Hartford Railroad, the present owner of the Naugatuck. This contains- a truck bolster having all the substantial elements of the McCarty combination, including the straight bar and flanges, the bent bar and the intervening columns, although, like the Old Metal Transom, it contained nothing corresponding to the plates P, which, as before observed, are only required in connection with a floating bolster. The ends of this bolster were fitted rigidly to the side trusses. The springs, instead of supporting the ends of the bolster, were placed over the journal bearings, and imparted a limited motion to the carriage. The guide plates are obviously unnecessary in this construction. The following drawings exhibit the McCarty bolster so far as the combinations of the third and fourth claims are concerned, and the corresponding features of the Naugatuck bolster: *118 The invention, then, of McCarty consisted in taking the Naugatuck truck or bolster, turning it into a floating bolster, by adding the guide plate, P, and resting its ends upon the springs in the side trusses, which springs, however, are not made an element of either the third or. fourth claims. Even if they had been claimed, they would not of themselves constitute a novel feature, as they are admitted to have been used long before, and are described in several prior patents "in connection with bolsters of the old pattern. The wedge-shaped blocks or columns M are unimportant, as angle irons in. analogous positions are well known in the art,, and are shown in prior patents. In addition to that, it does not appear that defendant used them. The Naugatuck truck was doubtless improved by the changes made by McCarty; but if there were anything more in this than mechanical skill, or the aggregation of familiar devices, each operating in its old way to produce an aggregated result, it was invention of such a limited character as to require a narrow construction. The case is not unlike that of the Pennsylvania Railroad v. Locomotive Truck Co., 110 U. S. 490, where a patent for employing a particular car truck, already in use on railroad cars, on the forward end of a locomotive, was held void for the want of novelty, the court referring to the familiar principle that the application of an old process or machine to a similar or analogous subject, with no change in the manner of application, and no result substantially distinct in its nature, will not sustain a patent, even if the new form of result has not before been contemplated. There is another consideration which leads to the same conclusion. The original application, made by McCarty, contained among other things a broad - claim for “ a truck bolster provided on its ends with supporting ánd guiding plates, substantially as and for the purpose set forth.”- This claim, being obviously too broad in view of the prior patents, was amended so as to read as follows: “ A truck bolster provided at its ends with plates which are notched to fit upon vertical parts of the frame so as to -serve as guides and supports for said bolster, substantially as set forth.” This claim having been apparently *119 rejected, the patentee abandoned his broad claim for a notched plate, and claimed only a plate in combination with the other features of his bolster, which was finally allowed. His acquiescence in the rulings of the Patent Office in this particular indicates very clearly that he should be restricted to the combination claimed, and that the case is not one calling for a liberal construction. In view óf these limitations upon the McCarty patent, was there any infringement in defendant’s device? This device contained the bars P and G-, and the pillars H of the McCarty patent, but instead of having the flanges Q upon the ends of the lower bar, and the guide plates P, there was substituted a cap shown in the patent to Montz, of which the following is a drawing: This cap contains a recess, i, for the reception of the ends of the bolster bar, which are thereby maintained in proper position with respect to each other, and is secured to the ends of the bolster bar by means of two bolts passing vertically through them. The cap, which fits between the posts of the side frame and rests upon a spring, is provided at each side with flanges, i', which. embrace the outer and inner faces of the posts, and prevent a longitudinal motion of the bolster, while permitting the same to move freely in a vertical direction. Now, as in view of the Naugatuck truck, there was nothing which could be called novel in the third and fourth claims of the McCarty patent, except the guide plates P, which were used to adapt this bolster to the purposes of a floating bolster by resting its ends on springs; and as the cap in question is an obvious de *120 parture from the device in this particular, we cannot say that it is an infringement, although it accomplishes practically the same purpose as the flanges Q and plate P of the McCarty patent. Had it been wholly novel to rest the ends of the bolster upon springs, by means of guide plates, it is possible we might have been able to hold this cap to be an infringement; but as the novelty consists, not in resting the ends of bolsters generally upon springs by means of a guide plate, but in so locating the ends of a bolster of a particular construction,-we think the employment of a different means of locating it avoids the charge of infringement. It is further claimed that the defendant is estopped to question the novelty of the McCarty patent and its priority of invention by the interference proceedings in the Patent Office. Aside from .the fact that the issues in those proceedings included the truss rods, which are not used by the defendant, the evidence that the' defendant was a party in privity to Montz’s application for the patent which was awarded to him, or that he made his application in their interest, is too inconclusive to justify us in holding that the company was bound by the result of this proceeding. It practically rests upon Montz’s reply to the question why he did not proceed with the interference, that he had no orders from his superior officers of the road. This we think is insufficient, in the absence of affirmative evidence that the company had knowledge of the proceeding, and assented to the action taken by Montz. There is not that certainty to every intent, which Lord Coke held necessary to constitute an estoppel, and as observed by this court in Russell v. Place, 91 U. S. 606, 610, “ If upon the face of a record anything is left to conjecture as to what was necessarily involved and decided, there is no estoppel in it when pleaded, and nothing conclusive in it when offered as evidence.” The decree of the court below dismissing the bill is, therefore, Affirmed.